Wireless Point-to-Point or Point-to-Multipoint Backhaul Solution

Flexibility With 4 Operational Modes
Bridge Repeater. In this mode, both interfaces are configured as static bridge interfaces. Packets are stored and forwarded between the two RF interfaces with full bandwidth 11Mbps. It's possible to use several AE3000-Ts if the distance between two locations is long beyond two units' transmission range.

Static AP Repeater. In this mode, one WLAN interface is configured as an AP interface, and the other is configured as a WDS-based bridge interface. The static AP repeater is suitable for situations in which Ethernet wiring between the AP and the network backbone is unaccessible, or for high cost on which the topology of the wireless bridging network is static.

Dynamic AP Repeater. In this mode, one WLAN interface is configured as an AP interface, and the other is configured as an AP client-based dynamic bridge interface. The dynamic AP repeater is suitable for situations in which Ethernet wiring between the AP and the network backbone is unaccessible, or for high cost on which the network topology is stellar (point-to-multipoint).

Dual AP. In this mode, both WLAN interfaces are configured as AP interfaces. The dual AP can handle twice the number of wireless clients than a normal AP. It can be treated as "two APs in a box."

Ease of Installation and Management
Through the neat Web-based user interface of the AE3000-T, the step-by-step installation instructions are easy to follow. And, the network administrator can centrally manage the AE3000-T via a Web browser or an SNMP MIB browser. The Windows-based Wireless Network Manager (WNM) utility enables you to view all AE3000-Ts within LAN via Auto Discovery regardless of IP address settings. The WDS link quality indicator and WDS link health monitoring features check signal quality based on a remote point-to-point testing mechanism for easy diagnostics. WNM provides versatile and cost-effective WLAN management functionality, including the ability to configure, control, monitor, update, report, diagnose and troubleshoot the WLAN via a single Window GUI.

Suitable for Public Wireless Access
The AP interface of AE3000-T contains features that are especially useful in public areas such as hotspots and enterprises. The wireless client isolation feature prevents wireless hackers from attacking other wireless subscribers computers. The AP load balancing feature enables wireless client associations and traffic load to be shared among all the APs within a group.

Ensure Great Security
The AP interface of AE3000-T can authenticate and authorize wireless users in organizations, enterprises, or public areas by the IEEE 802.1x standard. It communicates with a back-end RADIUS (Remote Authentication User Dial-In Service) server to see if a wireless user is allowed to access the wireless network. Windows XP has built-in support for IEEE802.1x. WEP and WPA are also supported for better wireless security.

Key Features
Wireless Two IEEE802.11g-based RF interfaces 4 operational modes: Bridge repeater, Static AP repeater, Dynamic AP repeater, and Dual AP WDS - static bridging AP client - dynamic bridging AP browsing with signal strength Preferred ESSID/BSSID selection Transmit power control Associated wireless clients status Data rate settings Security 64/128-bits WEP WPA - TKIP/IEEE 802.1x EAP-MD5, EAP-TLS, EAP-TTLS and PEAP support Disabling SSID broadcasts MAC-address-based access control VPN passthrough Public hotspots Link integrity Wireless client isolation AP load balancing Association control Networking DHCP client & server Current DHCP mapping table Packet filtering (Ethernet/TCP/UDP/Port) Management Rich set of tools for remote management: Web-based, Windows-based and UPnP Secure administration SNMP v1 & v2 SNMP traps: Standard and private traps MIB II, IEEE 802.11, IEEE 802.1d, IEEE 802.1x, and private enterprise MIB System log WDS link health monitoring WDS link quality indicator Firmware upgrade via HTTP and TFTP Configuration backup & restore Hardware watchdog timer
Interface
Ethernet	IEEE802.3u 10/100BaseTX Ethernet (RJ-45)
Antenna	One 2.4GHz rubber R-SMA detachable antenna
COM	One RS-232 port
Wireless
Frequency	2.4-2.4835 GHz, Direct Sequence Spread Spectrum (DSSS)
Data Rate	OFDM@54/48/36/24/18/12/9/6Mbps, CCK@11/5.5Mbps, DQPSK@2Mbps and DBSK@1Mbps
Channel	USA: 1-11 (FCC) Canada: 1-11 (IC) Europe: 1-13 (ETSI) France: 10-13 Japan: 1-14
Transmit Power	802.11b17dBm 802.11g 6/9Mbps17dBm, 12/18Mbps15dBm, 24Mbps14dBm, 36Mbps14dBm, 48Mbps 12dBm, 54Mbps12dBm
Receiver Sensitivity	802.11b 8% FER@1Mbps-91dBm,8% FER@2Mbps-88dBm 8% FER@5.5Mbps-85dBm,8% FER@11Mbps-83dBm 802.11g 10% PER@6Mbps-88dBm,10% PER@9Mbps-87dBm 10% PER@12Mbps-84dBm,10% PER@18Mbps-82dBm 10% PER@24Mbps-79dBm,10% PER@36Mbps-75dBm 10% PER@48Mbps-69dBm,10% PER@54Mbps-68dBm
Physical & LED
Dimensions	220mm (L) x 142mm (W) x 40mm (H)
LEDs	Power, LAN Link/ACT, 2 * RF Link/ACT, System alive
Environmental
	Temperature	Humidity
Operating	0-55°C	5%-95% (non-condensing)
Storage	-20-70°C	5%-95% (non-condensing)
Power Supply
Operating Voltage	DC +12V
Power over Ethernet	IEEE 802.3af compliant and PowerDsine certified (optional)
Ordering Information
AE3000-T6S13X	IEEE 802.11g Dual-Radio Repeater
AE3000-T6S13XE	IEEE 802.11g Dual-Radio Repeater w/POE